Safety Warning
WARNING:
All firearms (guns) are potentially dangerous if incorrectly used. Contenders and Encores are no exception, and each has unique features the user must understand to avoid accidental discharges which can result in damage to property, injuries, or death. Both the Contender and the Encore are designed such that in certain situations the hammer can rest on the firing pin, and if the hammer is struck or partially withdrawn and released with a live round in the chamber, the gun can fire.
The use of hammer extensions provides for a safer grip on the hammer, especially when access to the hammer is hindered by the presence of a telescopic sight; however, the projection of the extension to the side also increases the risk of snagging on a gun case, fabric on a car seat, brush, clothing, or any number of materials that may be present.
ALL users of Contenders and Encores must understand the design limits of these guns, whether an extension is used or not, to avoid accidents related to the operation of the hammer. Understanding these design limits and exercising correct procedures is essential to safe handling of both types of guns.
The Contender is similar to the old familiar Colt single action revolvers, for example, in that the hammer and firing pin can rest on the primer of a live round if the hammer is not drawn back to half cock. If the gun is dropped on its hammer or the hammer is otherwise struck, it may fire. The Contender will do much the same thing if the hammer is not moved to a safe position. IF THE CONTENDER HAMMER IS ALLOWED TO REST ON THE FIRING PIN WITH A LIVE ROUND IN THE CHAMBER, THE GUN MAY FIRE IF THE HAMMER IS STRUCK, IF THE GUN IS DROPPED ON THE HAMMER, OR IF THE HAMMER IS DRAWN PART OF THE WAY TO THE REAR AND RELEASED.
Correct Procedure for the Contender is to always open and close the barrel to reset the hammer block safety, which moves the hammer back and prevents it from contacting the firing pin when the hammer is not cocked. NEVER LOWER THE HAMMER AND LEAVE IT RESTING ON THE FIRING PIN. IF YOUR HAMMER HAS THE SLIDING CROSS BOLT SAFETY OR SELECTOR ON THE HAMMER, ALWAYS BE CERTAIN THE SAFETY IS IN THE SAFE POSITION UNTIL YOU ARE READY TO FIRE.
ENCORES:
The newer ENCORE has an entirely different trigger, sear, and hammer mechanism than the Contender. It is designed so that removing the trigger finger from the trigger automatically causes the sear to push the hammer back and hold it in a position that corresponds to a "half cock," off of the firing pin. However, if the mechanism malfunctions and the hammer is resting on the firing pin, just like the Contender the ENCORE can also fire if the hammer is struck, the firearm dropped on the hammer, or if the hammer is drawn to the rear and released.
Encore frames that have had a trigger job performed on them are most prone to this malfunction if the pull weight is too light and/or there is inadequate tension from the sear spring to push the hammer back to half cock, or if the hammer spring is too long.
ALWAYS BE CERTAIN THE ENCORE'S HAMMER IS NOT RESTING ON THE FIRING PIN.
If the mechanism of either the Contender or Encore is not functioning as described, or if you have any doubt at all about the manner in which these firearms function:
1) Contact Thompson/Center Arms if the frame is in factory original condition, or
2) If it has been modified contact an authority who specializes in Encores to evaluate your frame for proper function and explain its function to you. The average dealer/gunsmith probably is not qualified.
Disclaimer:
The sellers and manufacturers of Bellm Hammer Extensions assume no liability for any loss, damage to property, injury, or loss of life resulting from the use of said hammer extensions. Installation and use of Bellm Hammer Extensions implies agreement to comply with all safety procedures and cautions detailed above and to be responsible to insure that others in their control are informed of these procedures and cautions as well. User assumes all risks associated with the use of Bellm Hammer Extensions.
Warranty:
Bellm Hammer Extensions are warranted to be free of defects in materials and workmanship. This warranty is limited to the replacement of the extension or the purchase price of the extension only.
Directions for Installation:
Contenders: Slide the extension as far forward as it will go. Tighten with Allen wrench provided. Do not over tighten to the point of bending the extension. Periodically check tightness to make sure extension is secure.
Encores: T-slots are not cut all the way through, leaving a constriction at one end of the slot, which prevents the extension from sliding forward and falling off. Tip of hammer spur will be nearly flush with rear of extension. Tighten with Allen wrench provided. Do not over tighten. Periodically check tightness to make sure extension is secure.
Index Page Home (Table of Contents) Hammer Extensions Page